The Common Access Redundancy Protocol, or CARP allows multiple hosts to share the same IP address. In some configurations, this may be used for availability or load balancing. Hosts may use separate IP addresses as well, as in the example provided here.
To enable support for CARP, the FreeBSD kernel must be rebuilt with the following option:
device carp
CARP functionality should now be available and may be tuned via several sysctl OIDs. Devices themselves may be loaded via the ifconfig command:
# ifconfig carp0 create
In a real environment, these interfaces will need unique identification numbers known as a VHID. This VHID or Virtual Host Identification will be used to distinguish the host on the network.
One use of CARP, as noted above, is for server availability. This example will provide failover support for three hosts, all with unique IP addresses and providing the same web content. These machines will act in conjunction with a Round Robin DNS configuration. The failover machine will have two additional CARP interfaces, one for each of the content server's IPs. When a failure occurs, the failover server should pick up the failed machine's IP address. This means the failure should go completely unnoticed to the user. The failover server requires identical content and services as the other content servers it is expected to pick up load for.
The two machines should be configured identically other than their issued hostnames and VHIDs. This example calls these machines hosta.example.org and hostb.example.org respectively. First, the required lines for a CARP configuration have to be added to rc.conf. For hosta.example.org, the rc.conf file should contain the following lines:
hostname="hosta.example.org" ifconfig_fxp0="inet 192.168.1.3 netmask 255.255.255.0" cloned_interfaces="carp0" ifconfig_carp0="vhid 1 pass testpast 192.168.1.50/24"
On hostb.example.org the following lines should be in rc.conf:
hostname="hostb.example.org" ifconfig_fxp0="inet 192.168.1.4 netmask 255.255.255.0" cloned_interfaces="carp0" ifconfig_carp0="vhid 2 pass testpass 192.168.1.51/24"
注: It is very important that the passwords, specified by the
passoption to ifconfig, are identical. The carp devices will only listen to and accept advertisements from machines with the correct password. The VHID must also be different for each machine.
The third machine, provider.example.org, should be prepared so that it may handle failover from either host. This machine will require two carp devices, one to handle each host. The appropriate rc.conf configuration lines will be similar to the following:
hostname="provider.example.org" ifconfig_fxp0="inet 192.168.1.5 netmask 255.255.255.0" cloned_interfaces="carp0 carp1" ifconfig_carp0="vhid 1 advskew 100 pass testpass 192.168.1.50/24" ifconfig_carp1="vhid 2 advskew 100 pass testpass 192.168.1.51/24"
Having the two carp devices will allow provider.example.org to notice and pick up the IP address of either machine should it stop responding.
注: The default FreeBSD kernel may have preemption enabled. If so, provider.example.org may not relinquish the IP address back to the original content server. In this case, an administrator may “nudge” the interface. The following command should be issued on provider.example.org:
# ifconfig carp0 down && ifconfig carp0 upThis should be done on the carp interface which corresponds to the correct host.
At this point, CARP should be completely enabled and available for testing. For testing, either networking has to be restarted or the machines need to be rebooted.
More information is always available in the carp(4) manual page.
本文及其他文件，可由此下載：ftp://ftp.FreeBSD.org/pub/FreeBSD/doc/。
若有 FreeBSD 方面疑問，請先閱讀 FreeBSD 相關文件，如不能解決的話，再洽詢
<questions@FreeBSD.org>。
關於本文件的問題，請洽詢 <doc@FreeBSD.org>。